Denali D7 LED Light Kit with DialDim Lighting Controller

Details

At more than 7600 lumens the DENALI D7 light pod is one of the brightest LED auxiliary lights in a compact package just under 4.5 inches in diameter. Each D7 features 7 high-intensity 10-watt LEDs that are focused through a proprietary single-piece optic specifically engineered to create a full bodied spot beam that can reach over 1275ft at an intensity of 1.0 lux. A pair of D7s will outshine 14 D2 lights and produces more than twice the light output of the D4. Not only are the new D7s incredibly bright but they’re strong too. The robust heatsink and Active Thermal Management work together to keep this high-powered lamp cool enough to maintain maximum light output when you need it most.

Because the new D7 has so much power there’s no need for a selection of optics. The standard optic set benefits from the raw intensity of this array to have best-in-class spot coverage at a distance perfect for picking out wildlife way beyond the range of your motorcycle’s normal high beam. With lumens to spare the D7’s optics were designed to preserve a near-flood-beam pattern resulting in an amazingly wide (125ft) beam that helps illuminate the sides of the road. In a way the combination of incredible intensity and optics that are neither too distance-focused or flood-oriented is the best of both worlds.

The DENALI D7 Light Pod can be used to upgrade your existing DENALI 2.0 light pods or matched with a DENALI CANsmart digital accessory controller.

• High-Intensity Series Cree LEDs outputting 7665 lumens per pod
• DrySeal™ Submersible Waterproof light and switch housings can withstand the most extreme environments
• Impact PC™ Polycarbonate bezels won’t crack fade or corrode like traditional aluminum bezels.
• LiveActive™ Thermal Management keeps the LEDs cool preventing the loss of light output from overheating
• Low profile mounting bracket with stainless-steel hardware included
• LEDs: (7) 10 Watt Cree XPL HI
• Power Draw: 5 Amps per pod
• Beam Distance: 1275ft
• Beam Width: 125ft
• Raw Lumens: 7665 per pod
• DataDim™ Compatible: Yes
• Operating Voltage: 12 VDC
• Pod Size: 4.4in Round x 3.9in Deep
• IP67 Waterproof & Submersible
• 24 inch wiring pigtail with 3 pin waterproof connector
  
  The ground-breaking DialDim™ Lighting Controller features a multicolor halo dimming switch that allows you to independently turn on/off and dim two sets of auxiliary lights from a single consolidated wiring harness. The LED halo switch displays your exact settings and allows for effortless dimming on the fly. The blue halo controls light set one and the green halo controls light set two; simply double click to switch between the two circuits.
  
  The controller also features high beam, turn signal, and horn inputs to unlock intelligent flash features that can cancel your aux lights with your turn signal, flash your aux lights as a turn signal, or strobe your lights when you sound your horn.
• Independently control two sets of lights on/off and intensity level using the single DialDim™ Switch. The blue halo controls light set one and the green halo controls light set two. Double click to switch between the two circuits.
• Your auxiliary lights will automatically switch between your selected dim setting to full intensity with the factory high beam switch. Simply connect the blue input wire to your vehicle high beam circuit to enable this feature.
• A clever 0% dim setting on the switch allows your lights to be "off" during normal driving conditions but will jump to 100% intensity with your vehicle high beam switch. The lights will also react to turn signal and horn inputs in this mode but will remain off when no inputs are detected.
• When enabled the main lights (blue circuit 1) will cancel in sync with your signal to prevent "washing out" your factory turn signal. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• When enabled your amber visibility lights (green circuit 2) will flash in sync with your factory turn signals. Simply connect the yellow and orange input wires to your vehicle turn signal circuit to enable this feature.
• When enabled your auxiliary lights on both circuits will strobe at 4Hz when you sound your horn. Simply connect the green input wire to your vehicle horn circuit to enable this feature.
• Both light circuits are electronically fused and can be set right from the switch itself! The halo will illuminate red to notify you when a circuit fused is tripped.
• Upon vehicle startup, the switch halo will flash green to indicate a healthy battery voltage, or flash red to indicate a battery voltage that is below 11.8v.
• If battery voltage drops below 10.8v the lights will not power on preventing you from being stranded. The switch halo will flash 4 red LEDs to indicate the low voltage condition.
  
  Includes:
  - (2x) LED Light Pods
  - (2x) Hinge Mounts with M8 Stainless Steel Hardware
  - (2x) 4 inch Wiring Pigtail
  - (1x) DialDim Smart Controller